Category Archives: coats and finishes

Adding a touch with tiles

If you read the recent posts about the kitchen backsplash installation, you may have noticed that we left a gap at the stove location. That gap was reserved for something different – a special kind of backsplash tile.

back-splash-03

During one of our many excursions hunting for salvaged materials, I came across a handful of beautifully painted Mexican style tiles. At the time I didn’t know where I could use them, but I bought them anyway, certain that there would be just the right place for them.

bathroom-25

The backsplash behind the stove has become that place. Another place that tells a story about frugality and the charm that some salvaged materials have to offer.

Why did I wait this long to do the installation? I needed to wait until the range hood was installed. The bottom edge of the hood was the starting point along which I lined up the tiles.

I often observed and admired artful ornaments, such as hand painted plate hung above the stove. In this case, Cathy and I decided that the whole backsplash behind the stove could become artful with these unique tiles.

back-splash-04

Related posts:

Finished 1st floor front door

While we are on the subject of doors, I should post an update on the coloring book exercise.

1st-floor-front-door-05

We got a lot of comments on the various coloring options for our front door to the 1st floor unit. We appreciated every single one – thank you to all who left a note!

Your preference, but even more so the rationales for your preference helped in the decision making process. We finally opted for #3.

1st-floor-front-door-06

That leaves us with a little bit of New Mexico experience, and hopefully with some good luck.

Related posts:

Paint removal – Part 6: Digging through doors

There are several aspects to time, such as age and duration. I sometimes have to wonder if there is a proportional relationship between the two.

doors-01

Take the original 100+ year old doors from our building – the age component. These are solid and heavy and had salvaging and reuse written all over them. Despite all the layers of paint we got the occasional glimpse of the buried treasure.

doors-02

The process of recovering that treasure is a familiar one. The Silent Paint Remover removes the bulk of the paint, followed by a layer of Soy Gel to take off the residue.

1st-floor-front-door-03

That leaves the wood clean and ready for sanding, which is quick and easy, except for the panel profiles, particularly the corners. Those required a lot of attention to detail – and are a time suck – which gets us to the duration component.

It feels like working on the paint removal has extended the duration of our project indefinitely. And refinishing 12 of these age-old doors certainly factors into that equation.

doors-03

The two coats of zero-VOC lacquer helps wrap up the refinishing and restores the doors to their old glory.

doors-01  doors-04

These doors will always be special to us, because of their quality, their age, and the time and tender loving care we put into them. This might just as well be the definition of salvaging.

Related posts:

Paint removal – Part 5: Battling baseboards

The original baseboards in the building are quite something. Something with quite a little bit of paint on it.

trim-010

There is a tall bottom piece with an ornate cap. The cap and bottom together stand about 10 inches tall and are both milled out of 100+ year old oak, most of it quarter sawn. And we have quite a bit of it, which is a blessing and a curse.

trim-011

These were items we wanted to keep out of the waste stream. The quality of the millwork begged for salvaging and reuse.

But we also have that tedious chemical archaeology ahead of us – the paint removal. How far should we take the salvaging and reuse, and when would it be time to draw a line in the sand and decide it is not worth it?

The decision tipped in favor of salvaging and reuse once we realized that even if we could afford to purchase all new baseboards, we wouldn’t be able to find baseboards in this kind of quality nowadays.

Let the paint stripping begin!

trim-stripping-01

The Silent Paint Remover usually removes the bulk of the paint, and does so at reasonable speed. But a couple hundred linear feet of baseboard take some time to work through. And we still had to apply a layer of Soy Gel to remove the remaining paint residue.

trim-012

Sanding the baseboards took some time too. The flat surfaces were easy and fast. The more intricate profiles required a scraper, steel wool and time. But with each pass the wood grain became a notch more beautiful, until it was ready to get lacquered.

trim-013

Staining the oak was out of the question! The natural color was part of the charm. Instead we stuck to our zero-VOC rule and opted for the clear, satin finish Acrylacq by SafeCoat. It made the warm honey color of the oak pop.

This was very frustrating but ultimately rewarding work. It was frustratingly slow and time consuming, but with payback in the beauty of the salvaged and refinished product – particularly when we consider what we started with.

trim-010  trim-014

Related posts:

Backsplash grouting

It’s time to put the finishing touches on the backsplash and to move on to the next big thing.

In this case, the finishing touch is the grouting. We used regular sanded grout, which is easier on our budget, compared to the epoxy grout that we used in most of the bathroom.

This is again a durability issue, but I don’t carry quite the paranoia about moisture management when it comes to the kitchen backsplash. We are talking about the occasional splash, rather than frequent water exposure such as in the shower stall.

The combination of cement board behind the backsplash, the stone tiles, the sanded grout and application of a stone tile and grout sealer should adequately manage that occasional splash, and will allow for easy clean up.

Related posts: